Tourism

Bike Repair Station

Tube Replacement Instructions

  1. Remove the wheel from your bike.
  2. Inspect the outside of the tire for glass or anything else poking out. Remove if found.
  3. Deflate the tire completely by letting the air out of the tube.
  4. Opposite the valve, wedge two tire levers (not a screwdriver!), next to each other, between the tube and the rim.
  5. Hold one tire lever in place and slowly work the other lever away from you, prying one side of the tire off of the rim. The edge of the tire you are prying against is called the bead.
  6. When one side is removed, remove the tire levers and pull the other bead off the rim.
  7. Inspect the inside of the tire for glass or anything else poking out. If there is a large hole in the tire, such that the inner tube can poke through, you may need to apply a temporary tire boot, and consider replacing the tire.
  8. Inspect the band of rubber, plastic, or cloth tape on the rim. Make sure it is covering the spoke holes on the rim.
  9. Put one tire bead back on to the rim.
  10. Inflate the new or patched tube a bit. This will make the next steps easier.
  11. Put the valve through the proper hole on the rim.
  12. Slowly work the tube inside the tire and on to the rim.
  13. Put the other bead of the tire back on the rim. If possible, do not use tire levers to do this. Use your hands instead.
  14. Once both beads are on the tire, using your hands, pry between the rim and the tire and make sure the tube is not sticking out anywhere. Do this on both sides of the tire.
  15. Inflate the tire to the pressure range recommended.
  16. Re-install the wheel onto your bike.

Manual Pump - Instructions 

1. Read the pressure range from the side of the tire.
2. Remove the cap from the tire valve. On Presta valves, loosen the tip of the valve.
3. Connect the tire valve to the pump nozzle and flip the lever up.
4. Using both hands, move the pump handle up and down. Stop when the desired pressure is reached.
5. Flip down nozzle lever and remove the nozzle from the tire.
6. Replace the cap on the tire valve. On Presta valves, re-tighten the tip of the valve first.
7. Happy riding!

Locations of bike repair stations in the City of Ottawa

Self Guided Bicycle Tours

As one of Canada’s largest cities at 100 kilometres wide by 50 kilometres deep, Ottawa has a very diverse and eclectic collection of rural attractions. These include historic sites, vineyards, county fairs, farmers’ markets, villages, and natural features. One of Ottawa’s greatest attractions is its beautiful waterways including the Ottawa River, Rideau Canal and Rideau River. Ottawa is also home to some of Canada’s most iconic buildings including: the Federal Parliament Buildings, the National Gallery, the National Arts Centre and many more. Seeing Ottawa by bicycle is very enjoyable and a great way to add fitness to your vacation experience. Build an appetite and then satisfy it at one of Ottawa’s great restaurants or quaint bistros and pubs.

Learn More

Videos: Bicycle Repair Stations

Changing Tire

Transcript: Changing a tire

Patching Tire

Transcript: Patching Tire

Pumping Tire

Transcript: Pumping Tire

Video Transcripts

Changing Tire

*Guitar strumming*

How to change a tire

  1. Place seat onto stand
  2. Remove wheel from bicycle
  3. Deflate the tube by pushing valve
  4. Break the seal between the tire bead and the rim
  5. Use the leaver to pull tire bead over the rim
  6. Slide lever around the wheel
  7. Remove the tube and hang safety off the ground
  8. Remove tire, and inspect tire and wheel for debris and damage
  9. Re-mount one tire bead mount tube at valve hole
  10. Tuck the tube into the tire
  11. Starting at the valve stem mount the other bead hook
  12. Apply pressure evenly with both hands around to the opposite side of the valve stem inflate your tire (see “how to pump a tire” video)
  13. Remount wheel into frame

Patching Tire

*Guitar strumming*

How to patch a tire

Before you watch this:

  • complete steps 1 to 7 of “how to change a tire”
  • Inflate tube as full as possible (see ‘How to pump a tire’ video)
  1. Maneuver tube to listen and feel for air escaping
  2. Identify the puncture and circle it with a marker
  3. Open your patch kit
  4. Choose the sandpaper, sand an area larger than the patch, until darker
  5. Apply glue
  6. Spread glue to a larger area than the patch
  7. Wait 3-5 min for glue to dry
  8. Test by touching edge (glue should be tacky)
  9. Select patch from the kit
  10. Firmly place the patch
  11. Roll finger to make sure the full surface area is covered

Now, refer back to ‘how to change a tire’ at the appropriate step:

  • If the tire may be damaged, proceed to Step 8. Otherwise, go to step 9.

Perform a visual inspection before riding

Pumping Tire

*Guitar strumming*

How to pump a tire

  1. Remove valve cap
  2. Presta valve and Schrader valve
  3. Loosen Presta valve and press to release air
  4. Unscrew Schrader cap, and place pump chuck
  5. Place the correct style of pump chuck onto the valve and lock into place.
  6. Note: there are 2 different slots in the pump head depending on which type of valve you have
  7. Pump and monitor the gauge.
  8. Inflate to recommended PSI, and defer to lower range on tire
  9. Close lever to unlock
  10. Screw in Presta valve, install valve cap and tighten lock ring
  11. Preform a final visual inspection before riding 

Troubleshooting the pump:  

*guitar strumming*