Skip to main content

Cycling safety

Cycling Safety Awareness Program

The Cycling Safety Awareness Program (CSAP) is an educational outreach program about cycling safety. 

Learn More

Sharing the road

A bicycle is a vehicle and must be treated the same as buses, large trucks, motorcycles and cars. This means that cyclists need to operate their bicycles like other vehicles on the road. Motorists must also respect a cyclist's right to ride on the street. Here are some tips to make everyone's road experience safer and more enjoyable.

Cyclists

Sharing with Motorists

  • Follow the rules of the road at all times.
  • Be bright at night! Use a headlight, taillight, reflectors and light-coloured or retro-reflective clothing so motorists can see you.
  • Motorists may not anticipate a cyclist, so ride defensively.
  • Never compromise your safety for the convenience of a motorist.
  • Where possible, ride in a straight line and avoid dodging between parked cars, into bus bays or around obstacles.
  • Know where you are going and look ahead to position yourself in the correct lane. Avoid being in a "right turn only" lane if you plan to proceed straight through an intersection.

Sharing with Pedestrians

  • Stay off sidewalks.
  • Yield to pedestrians at crossings.
  • Stay out of crosswalks when waiting at intersections - stopping here forces pedestrians into traffic.
  • Watch for pedestrians when pulling into or out of driveways, parking lots or anywhere you have to ride across a sidewalk.
  • Keep an eye out for pedestrians when turning, especially on one-way streets. While vehicles may only travel in one direction, pedestrians cross both ways.
  • Be especially careful where children might be walking - near schools, day cares and pathways.
  • Watch for pedestrians on roads that don't have sidewalks. They should be walking on the shoulder facing on-coming traffic.

Sharing with Buses

  • Avoid riding in the blind spots at the sides and rear of the bus where the operator cannot see you. If you can't see the operator's eyes in the bus's mirror, she or he can't see you.
  • Stay well back and to the left side of the bus and remember that buses make frequent stops.
  • Always pass a bus on the left side. Don't get trapped between the bus and the curb.
  • Allow plenty of room when passing a bus, and never race.
  • Avoid repeat passes ('leap-frogging').
  • Stay out of bus bays when cycling.
  • On Albert and Slater Streets ride in the far left lane to reduce conflict with turning vehicles. To make a right turn, signal and change lanes one at a time.

Sharing with Trucks

  • When stopping behind a truck, remember that it may need space to roll back when it starts up again, especially on a hill.
  • See and be seen: trucks have large blind spots on both sides, directly behind and in front. Stay away from these areas as much as possible. If you're cycling behind a truck and you can't see one of its side-view mirrors, the truck driver can't see you.
  • Give turning trucks lots of room. Never pull up into the open space on a truck's side if the driver has signalled a turn because the driver may be setting up or completing a turn.
  • The size of the truck will directly affect the size of the blind spots, length of time it takes to stop, and the amount of space needed for turns.

Motorists

  • Follow the rules of the road at all times.
  • Bicycles are considered vehicles under the Highway Traffic Act, so treat them as you would any other vehicle on the road.
  • Cyclists generally ride in the right-most through lane, about one metre from the curb or parked cars.
  • People who ride bicycles are not obligated to use bike lanes or pathways, and are entitled to cycle on all roads in Ottawa except the Transitway, Highways 416, 417 and Regional Road 174 (to Orléans).
  • Motorists are prohibited from driving or parking in all designated bicycle lanes.
  • When passing a cyclist, the Highway Traffic Act requires that you leave a safe distance between your car and the bicycle. Extra passing distance should be given when slippery road conditions exist.
  • Cyclists are entitled to ride in the centre of a lane when they feel it is too narrow for a motor vehicle to pass them, or if they feel their safety is compromised.
  • Slow down or avoid puddles when passing cyclists.
  • Cyclists can ride on either the paved road, paved shoulder or unpaved shoulder in rural areas.
  • Drivers of larger vehicles should be cautious of blasting a cyclist with winds when passing, especially on dusty roads.

As a reminder about sharing the road, you can watch the following videos:

Cycling education programs

Become more comfortable and confident on the road, learning assertive cycling skills, traffic analysis, general bicycle maintenance, route planning and more. The City's cycling programs have been developed using the Canadian Cycling Association's CAN-BIKE program. CAN-BIKE is oriented toward recreational and utilitarian cycling. Instructors are nationally certified highly skilled cyclists.

Programs are offered from April through to October across the city.

Got a Bike Club? Sign your group up for a lesson.

See you on the road.

Contact

Cycling education courses for children

Bike RODEO – ages 6-10 – 2 hours

Essential bicycle handling and traffic skills for young cyclists in a fun festival type atmosphere. Topics include helmet fitting, bicycle maintenance, handling, signalling, gears, braking, avoiding road hazards and more. Participants must know how to ride.

Learn to Ride Private Lessons – ages 6 and up

For children and youth who cannot ride a bike. Participants will learn to balance, start, stop and turn. One 2-hour or two 1-hour sessions are offered on a one to one basis. Participants must have a bicycle and helmet. Instructors will meet you at your local school parking lot.

Cycling Safety for Kids – ages 9-13 – 4 hours

Essential bicycle handling and traffic skills for young cyclists. Helmet fitting, bicycle maintenance, handling, signalling, gears, braking, avoiding road hazards and more. Participants must know how to ride.

CAN-BIKE for Kids – ages 9-13 – 8 hours

Learn steering, signalling, right and left turns, changing gears, braking and avoiding road hazards. Young cyclists are taught to ride safely to school or to the local swimming pool on residential streets. Participants must know how to ride.

Rural Cycling for Youth – ages 14-17 – 4 hours

Enhance cycling skills for teenagers with riding experience. Maintenance, handling, hazard avoidance, emergency manoeuvres and learning to ride more safely in low-traffic areas.

Cycling education courses for adults

Commuter Cycling Safety – ages 14+ – 4 hours

Improve your confidence and ability to ride safely in traffic. Learn traffic theory and assertive cycling techniques. You must have basic experience cycling in low traffic areas.

CAN-BIKE I – ages 15 and up – 12 hours

Designed for both beginner and occasional cyclists, learn to ride confidently and safely in low traffic areas and on recreational pathways. Bike care, minor repairs, riding techniques, detecting and avoiding hazards, and emergency manoeuvres.

CAN-BIKE II – ages 15 and up – 18 hours

Assertive cycling is for commuters and recreational cyclists who already ride in traffic. Review riding skills, cycling proficiency, bicycle maintenance, health and fitness, equipment and bicycle consumerism. Pre-requisite for instructor training.

CAN-BIKE Commuter Cycling Safety – ages 18+ – 6 hours

Cycling to school or work offers significant challenges to both novice and experienced cyclists. One-day course for recreational and commuter cyclists who want to improve their competence and comfort level in traffic. Learn to recognize and react to common road hazards. Traffic problems are presented, then ridden through and discussed. Learn about the legal status of bicycles and essential bicycle handling techniques.

Cycling Skills for Women – 4 hours

Learn riding skills, bike maintenance, equipment, health and fitness. Specific topics such as night security and riding with children are explored. Female instructors.

Adult Learn to Ride Private Lesson – 1 hour

For adults who cannot ride a bike. Learn to balance, start, stop and turn. One session, on a one-to-one basis. You must have a bicycle and helmet.

Cycling Skills for Seniors – ages 50 and over – 3 hours

Learn the skills to ride confidently and safely in traffic areas and on recreational pathways. Bike care, minor repairs, riding techniques, detecting and avoiding hazards and emergency manoeuvres, helmet fitting, route planning and pathway safety.

CAN-BIKE Instructor Workshops – ages 16 and up – 18 hours

Workshops are open to CAN-BIKE II graduates with recommendations from their instructor. Develop effective teaching skills, course planning and risk management. Excellent rates of pay, flexible schedule and great opportunities. Instructors who complete all requirements and teach a minimum of three courses in the first year will be subsidized for 50 per cent of the costs affiliated with becoming a certified instructor.

Signs and markings

  

Bicycle route

The bicycle route sign indicates those streets that form a part of the Bicycle Route Network. These streets are shown on the Ottawa Cycling Map.

  

Bicycle lane

Bicycle lanes are marked with a solid white line, typically 1.5 to 2.0 metres from the curb or edge of road. Bicycle symbols are painted at regular intervals to indicate that these lanes are for use by cyclists.

  

Reserved bicycle lane

Reserved lane signs indicate that lanes are reserved for use by specific vehicles such as buses, taxis, high-occupancy vehicles and bicycles.

  

Contra-flow bicycle lane

On streets with contra-flow bicycle lanes, cyclists are permitted to travel in both directions while motorists are restricted to one direction only. Cyclists travelling with the flow of motor vehicle traffic should ride on the right-hand side of the street. Cyclists riding in the opposite direction (or 'contra-flow') must use the designated lane provided.

  

Bicycle detour

Bicycle detour signs indicate an alternate route for bicycles where construction activities require closure of the usual bicycle route.

  

Bicycle parking

Look for the bicycle parking sign to indicate where bicycle racks or supervised bicycle parking may be found.

  

Bicycles excepted

This tab is typically found with signs whose purpose is to restrict the movements of motor vehicles. By excepting bicycles, the travel environment for cyclists is improved.

  

Dismount and walk

In certain locations, cyclists are encouraged to act as pedestrians and should dismount and walk their bicycles. Please respect these signs.

  

Motorized vehicle passing prohibited

This sign shows where motorists must not overtake a cyclist within a specified zone.

  

Bicycle crossing ahead

This sign indicates to motorists that they are approaching a location where bicycles may be crossing the road.

  

Share the road

Motorists are reminded to provide adequate space for cyclists and to use extra caution where these signs are posted. Motorists must always share the road, whether these signs are displayed or not.

  

Three yellow dots

These three dots are painted at intersections and indicate the most responsive part of a metal-detecting loop embedded in the pavement. This loop senses when a vehicle, including a bicycle, is stopped and changes the signal from red to green.

  

Cycling prohibited

Riding your bicycle may be prohibited on certain roadways, such as 416, 417 and regional road 174 (to Orléans) and the Transitway.

[top]

Cycling and the law

Collisions

The law requires every operator of a vehicle to identify him- or herself to the other driver and to report the collision to the police if there are injuries or damages in excess of $1,000.

If you are involved in a collision:

  • Give your name, address and phone number to the other driver(s).
  • Get the other driver(s) name, address, phone number, vehicle particulars and insurance company and policy number.
  • Call the police if there are injuries.
  • Settle damages between yourselves, but only if damages are minor (less than $1,000). Keep in mind that “no fault” insurance in Ontario means you can't make a claim against the other driver’s insurance, but you can still sue the driver personally.
  • Call the police if the damages exceed $1,000. The police may ask you to come to the station to make a report. Explain that getting to the nearest station may not be feasible because you are on a bicycle.
  • Obtain names of any witnesses that may be available. If anyone has stopped to help at the collision, ask for their name(s) and telephone number(s).
  • Write out a short paragraph describing what happened if the police will not be responding to the scene. Have everyone involved sign it. Keep this for future reference.

Avoid getting into a collision by taking a CAN BIKE course.

Equipment

According to the Highway Traffic Act, your bicycle must be equipped with:

  • A bell or horn in good working order
  • At least one braking system on the rear wheel capable of skidding that wheel on dry, level pavement
  • A white front light (visible from a distance of at least 150 metres)
  • A red rear light or red rear reflector
  • Two strips of white reflective tape on front forks (each strip to be 125mm by 25mm)
  • Two strips of red reflective tape on rear forks

These lighting requirements are mandatory if you are riding between half an hour before sunset and half an hour after sunrise, or anytime visibility has been reduced to the point where you cannot see 150m ahead.

Electric bikes (e-bikes) that physically resemble traditional bikes are permitted on City of Ottawa bike paths. An electric bicycle is a bicycle that is powered with an electric motor. It uses rechargeable batteries and can travel up to 24 to 32 kilometres per hour.

Scooter type power assisted devices and bicycles with a non conventional appearance are NOT permitted on the pathways because they tend to be heavier and therefore have an increased risk to health and safety in the event of a collision.

These rules do not apply to mobility devices such as powered wheelchairs, three wheel electric scooters and four wheel electric scooters.

Helmets

Bicycle helmets must be worn by all cyclists under the age of 18. Look for the CSA or CPSC certification in the helmet before you buy or wear it.

  • To provide maximum protection, the helmet should fit level and square on the head, and the front should cover the forehead.
  • It should sit snugly on and not slip when the head is moved around, even before the chin strap is fastened.
  • The straps should be adjusted to meet just below the ear, and fastened comfortably. For more information, contact Ottawa Public Health Information at 613-580-6744.

Rules of the pathways

Bicycles are permitted on mixed-use pathways, but cyclists should follow these guidelines:

  • Keep to the right of the yellow centre line (where one exists)
  • Pass other users only when it is safe to do so
  • Use your bell or voice to warn others when you are passing e.g., "Passing on your left!"
  • Ride at a suitable speed for a mixed-use pathway (recommended speed of no more than 20 km/hr)
  • Be cautious at night, especially along pathways that are not lit. Ride more slowly, especially around dark curves, and stay visible by dressing brightly and using bicycle lights.

Rules of the road

Cyclists must identify themselves when stopped by police for a contravention of the Highway Traffic Act or municipal by-law regulating traffic. You just need to provide your correct name and address.

Cyclists are to ride as close as practicable (i.e., no closer than 1.0 metre) to the right curb of the roadway, except when:

  • Travelling at the normal speed of traffic
  • Avoiding hazardous conditions
  • The roadway is too narrow for a bicycle and a motor vehicle to travel safely side-by-side
  • Riding alongside another cyclist in a manner that does not impede the normal movement of traffic
  • Preparing to make a left turn, passing another vehicle, or using a one-way street (in which case riding alongside the left curb is permitted)

Cycling on the sidewalk is prohibited by the City of Ottawa Traffic and Parking By-law except where it is permitted by official or authorized signs.

Please refer to the Ministry of Transportation Ontario site for updates to the Highway Traffic Act including the 1 metre passing law and new fines and penalties for dooring.

Cyclists who frequently ride in Québec should become familiar with the details of the Code de la sécurité routière from the Québec Ministry of Transport.
 

Children and cycling

Children should be taught that cyclists must follow the same rules as vehicles. As adults, we often take for granted that children know how traffic works and what signs mean. Practice and experience, combined with adult supervision, will reinforce good cycling behaviour. Parents can set a good example by wearing bike helmets themselves.

Is your child ready to cycle to school without an adult?

Your child wants to ride a bicycle to school and you're worried. Keep in mind that children under the age of nine don’t have the skills to cycle safely without adult supervision and that all cyclists under 18 must wear a helmet. Consider these other factors:

Can your child handle a bicycle well enough to:

  • Check over his or her shoulder while travelling in a straight line 
  • Brake quickly and confidently to stop at a predetermined point 
  • Ride with one hand while displaying clear hand signals

Can your child demonstrate these skills:

  • The ability to gauge the speed of other vehicles
  • Knows right from left
  • The ability to concentrate on a task and avoid distractions
  • The ability to lock up the bicycle on his or her own

Does your child understand the rules of the road, such as:

  • What yield means and where he or she is expected to do so 
  • What "right of way" means 
  • What cycling-related road signs mean and where to look for them

For more information on how to get your children ready to cycle, contact the Envirocentre at 613-580-2424, ext. 27399 or Safe Kids Canada at 1-888-SAFE-TIPS. Consider enrolling your child in a CAN BIKE class with the City.

Taking your child with you

 There are many options for bringing children on a bike trip. The best option for you depends on the age of your child.

Infants

Don’t cycle with infants who do not have sufficient neck strength to hold their heads up while wearing a helmet. Wait until your child is able to sit up on his or her own and can wear a properly fitted, certified bicycle helmet.

Toddlers

Transport toddlers in a bicycle trailer or in a seat mounted to the bicycle frame. Always make sure your toddler is wearing a properly fitted bicycle helmet and that the equipment is firmly secured to the bicycle.

Trailers

Bicycle trailers offer a more stable and secure environment for your toddler. Unfortunately, trailers are less visible and your child is farther away from you. Attach an orange safety flag to the trailer for greater visibility and try to ride with another adult behind the trailer.

Rear-mounted seats

A rear-mounted seat brings your child closer to you when cycling. However, these seats shift the bicycle's centre of gravity and can make it unstable. Parents who wish to use a rear-mounted seat should first practice riding with a weight comparable to the child's in the seat. A good seat has a high back, a lap and shoulder harness, and foot guards to protect feet from the spokes.

Front-mounted seats

Front-mounted seats vary in design and placement on the bicycle. Avoid seats mounted to the handlebars, as these can disrupt steering control. Other front-mounted seats that attach to both the seat and handlebar stems are more stable and keep your child in front of you, allowing for a more watchful eye on the child and the road.

Young children

Young children can ride on their own or with mom and dad using a trailer-bike. This device attaches to the seat post and transforms an adult bicycle into a tandem bike for kids. It is especially useful for longer trips where young children don't have the stamina to ride on their own. Remember that children should wear a properly fitted, certified bicycle helmet when using a trailer-bike or cycling on their own.
 

Reporting Hazards

Potholes and other hazards in the road surface can be problematic for all road users. Bicycles are more susceptible than motor vehicles to irregularities in pavement conditions, and riding into or swerving to avoid a hazard increases the risk of injury.

The City responds to thousands of requests to repair potholes every year and residents can use Service Ottawa to report road surface hazards such as this. Service Ottawa allows residents to notify the City of cycling hazards that apply to roads and multi-use pathways. Some of the Service Ottawa categories that may assist cyclists in reporting hazards include: potholes, road repair needed, manhole cover problems, street lighting, debris and sidewalk and path maintenance.

You may also report a vehicle parked in bike lanes.

You can as well notify the City of these hazards by dialling 3-1-1 or visiting your local Client Service Centre.

Bike Maps

Did you have a near miss on your bike to work today? BikeMaps.org  is a web map where you can contribute to a safer cycling environment by reporting cycling incidents, including: collisions, near misses, hazards, or thefts. Only a third of cycling collisions are collected officially, leaving the vast majority of incidents unreported. Logging an incident with BikeMaps.org is anonymous and only takes a minute or two using either a web browser or the free mobile app (android or iOS devices). You can also create a riding area on the website to receive alerts of new reports.

The information collected from cyclists in the City of Ottawa will assist staff with identifying locations that may require engineering, education or enforcement campaigns. BikeMaps.org is a research project that began in 2014 at the University of Victoria. Since then they have received over 3200 incident reports worldwide. Funding from the Public Health Agency of Canada has enabled expansion to other Canadian cities such as Edmonton and Ottawa. The initiative is supported by the Safer Roads Ottawa program and its partners.

BikeMaps.org welcomes all feedback and interest in the project. Get in touch by email info@bikemaps.org, on twitter @BikeMapsTeam, or through Facebook (/BikeMaps.org).

Bike Repair Station

Tube Replacement Instructions

  1. Remove the wheel from your bike.
  2. Inspect the outside of the tire for glass or anything else poking out. Remove if found.
  3. Deflate the tire completely by letting the air out of the tube.
  4. Opposite the valve, wedge two tire levers (not a screwdriver!), next to each other, between the tube and the rim.
  5. Hold one tire lever in place and slowly work the other lever away from you, prying one side of the tire off of the rim. The edge of the tire you are prying against is called the bead.
  6. When one side is removed, remove the tire levers and pull the other bead off the rim.
  7. Inspect the inside of the tire for glass or anything else poking out. If there is a large hole in the tire, such that the inner tube can poke through, you may need to apply a temporary tire boot, and consider replacing the tire.
  8. Inspect the band of rubber, plastic, or cloth tape on the rim. Make sure it is covering the spoke holes on the rim.
  9. Put one tire bead back on to the rim.
  10. Inflate the new or patched tube a bit. This will make the next steps easier.
  11. Put the valve through the proper hole on the rim.
  12. Slowly work the tube inside the tire and on to the rim.
  13. Put the other bead of the tire back on the rim. If possible, do not use tire levers to do this. Use your hands instead.
  14. Once both beads are on the tire, using your hands, pry between the rim and the tire and make sure the tube is not sticking out anywhere. Do this on both sides of the tire.
  15. Inflate the tire to the pressure range recommended.
  16. Re-install the wheel onto your bike.

Manual Pump - Instructions 

1. Read the pressure range from the side of the tire.
2. Remove the cap from the tire valve. On Presta valves, loosen the tip of the valve.
3. Connect the tire valve to the pump nozzle and flip the lever up.
4. Using both hands, move the pump handle up and down. Stop when the desired pressure is reached.
5. Flip down nozzle lever and remove the nozzle from the tire.
6. Replace the cap on the tire valve. On Presta valves, re-tighten the tip of the valve first.
7. Happy riding!

Locations of bike repair stations in the City of Ottawa

Videos: Bicycle Repair Stations

Changing Tire

Transcript: Changing a tire

Patching Tire

Transcript: Patching Tire

Pumping Tire

Transcript: Pumping Tire

Video Transcripts

Changing Tire

*Guitar strumming*

How to change a tire

  1. Place seat onto stand
  2. Remove wheel from bicycle
  3. Deflate the tube by pushing valve
  4. Break the seal between the tire bead and the rim
  5. Use the leaver to pull tire bead over the rim
  6. Slide lever around the wheel
  7. Remove the tube and hang safety off the ground
  8. Remove tire, and inspect tire and wheel for debris and damage
  9. Re-mount one tire beadMount tube at valve hole
  10. Tuck the tube into the tire
  11. Starting at the valve stem mount the other bead hook
  12. Apply pressure evenly with both hands around to the opposite side of the valve stemInflate your tire (see “how to pump a tire” video)
  13. Remount wheel into frame

Patching Tire

*Guitar strumming*

How to patch a tire

Before you watch this:

  • complete steps 1-7 of “how to change a tire”
  • Inflate tube as full as possible (see ‘How to pump a tire’ video)
  1. Maneuver tube to listen and feel for air escaping
  2. Identify the puncture and circle it with a marker
  3. Open your patch kit
  4. Choose the sandpaper, sand an area larger than the patch, until darker
  5. Apply glue
  6. Spread glue to a larger area than the patch
  7. Wait 3-5 min for glue to dry
  8. Test by touching edge (glue should be tacky)
  9. Select patch from the kit
  10. Firmly place the patch
  11. Roll finger to make sure the full surface area is covered

Now, refer back to ‘how to change a tire’ at the appropriate step:

  • If the tire may be damaged, proceed to Step 8. Otherwise, go to step 9.

Perform a visual inspection before riding

Pumping Tire

*Guitar strumming*

How to pump a tire

  1. Remove valve cap
  2. Presta valve and Schrader valve
  3. Loosen Presta valve and press to release air
  4. Unscrew Schrader cap, and place pump chuck
  5. Place the correct style of pump chuck onto the valve and lock into place.
  6. Note: there are 2 different slots in the pump head depending on which type of valve you have
  7. Pump and monitor the gauge.
  8. Inflate to recommended PSI, and defer to lower range on tire
  9. Close lever to unlock
  10. Screw in Presta valve, install valve cap and tighten lock ring
  11. Preform a final visual inspection before riding 

Troubleshooting the pump:  

*guitar strumming*